Exactly How to Remove and Change a Bathtub
Exactly How to Remove and Change a Bathtub
Blog Article
This post following next in relation to Tools You Need to Install a New Bathtub is quite enjoyable. Give it a try and make your own results.
Setting up a bathtub isn't specifically rocket science, but it does call for solid plumbing, woodworking, as well as in some cases, tiling abilities. Changing an old bathtub with a brand-new one is likewise a moderately tough project. If the old bathtub is readily easily accessible, the project can relocate rapidly; if you have to open a wall surface to remove the old bathtub and place the new bath tub, the task is much harder. In either situation, the project is within a residence handyman's skills, although you will certainly need an assistant to leave the old bathtub as well as embeded in the new one. See to it you have certified yourself for the work and also are comfortable trying it. Instead of working with a specialist to take control of a halfway-completed job, it is much better to consider utilizing one prior to you start. Chances are you might need a specialist plumber to make tube connections.
This write-up will aid you set up a brand-new tub in your washroom if you have currently acquired a brand-new bathtub and do not require to transform the arrangement of your previous supply of water pipelines.
Your tools and also material list should make up the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your installment, then the first thing you ought to do is separate the water system. After doing so, activate the taps to drain any kind of water continuing to be in the system. The procedure of removing the existing taps can be rather bothersome due to the restricted gain access to that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the faucets. Have a towel ready for the remaining water that will originate from the pipelines. As soon as the supply pipelines have been removed, utilize the same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the single faucets from transforming during this process. When the faucets have actually been removed, the holes in the bath/basin will have to be cleansed of any kind of old sealing compound.
Before going on to fit the brand-new taps, compare the pipe links on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic adapter to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet and the other end offers a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly require decreasing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin ensuring that the washers are in place between the tap and the sink. Secure the tap in place with the manufacturer offered backnut. Once the tap is securely in place, the supply pipes can be connected to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular tap connectors. The former type should be connected to the tap finishes first, tightening only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Setting up the Tub
Utilizing both wood boards under its feet, put the tub in the required position. The wood boards are handy in equally spreading out the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto four small factors.
The following objective is to guarantee that the bathtub is leveled all round. This can be achieved by examining the level as well as changing the feet on the bathtub till the spirit level reads degree.
To set up taps, fit the bottom of the outermost versatile tap connector to the suitable supply pipe by making a compression sign up with; after that do the very same for the various other faucet.
Activate the water supply and also check all joints and new pipework for leaks and tighten them if necessary. Fill up the bathtub and likewise inspect the overflow outlet and the regular electrical outlet for leaks.
Finally, deal with the bath paneling as described in the manufacturer's instruction manual. Tiling and sealing around the bath tub needs to wait until the bathtub has been used at least once as this will certainly resolve it into its final setting.
Getting ready for the Setup
Firstly, the sustaining structure supplied with the bath should be fitted (if called for) according to the maker's directions. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is very important to make certain that if the tap features a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is likewise sensible to fit a supporting plate under the faucets system to prevent stress on the bathtub.
Fit the adaptable faucet adapters to the bottom of the two faucets utilizing 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you make use of all of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath must currently be ready to be suited its last position.
Tiling Around the Tub
In the location where the bath satisfies the tile, it is essential to seal the accompanies a silicone rubber caulking. This is very important as the installation can move sufficient to crack a stiff seal, creating the water to permeate the wall surface between the bathroom and also the tiling, resulting in difficulties with moisture and also possible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your fixtures as well as installations. They are sold in tubes and also cartridges, and can securing gaps as much as a size of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of drenched paper or soft rope. Remember to always fill up the bathtub with water prior to securing, to permit the movement experienced when the tub is in usage. The sealer can crack relatively very early if you do not take into account this motion prior to securing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally easily available on the market. It is recommended to fit the ceramic tiles utilizing water-resistant or water resistant sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was shown that editorial on Installing A Bathtub from an acquaintance on a different web address. Do you know another individual who is enthusiastic about the niche? Why not promote it. I enjoy reading our article about Installing A Bathtub.
Give Me A Quote!
Report this page